單項選擇題

Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on  External_B fails? ()


A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1



您可能感興趣的試卷

你可能感興趣的試題

2.多項選擇題What three tasks must a network administrator perform to properly configure Hot Standby Routing  Protocol (HSRP)?()

A. Define the encapsulation type.
B. Define the standby router.
C. Define the standby IP address.
D. Enable the standby priority.

3.單項選擇題

Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4.  When Link A fails, router R2 (Link B) becomes the active router. 
Which router will assume the  active role when Link A becomes operational again?" ()

A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the  event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the  event of Link B failure.
D. The third member of the HSRP group, router R3, will take over the active role only in event of  router R2 failure.

4.單項選擇題

Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1  and R2, and hosts A and B have been configured as shown. 
Which statement can be derived from  the exhibit?()

A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin, load-balancing mode has been configured.
D. The GLBP host-dependent, load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.

5.單項選擇題

Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on  External_B fails?()

A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1

最新試題

Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()

題型:單項選擇題

Which statement is correct about RSTP port roles?()

題型:單項選擇題

What two things will occur when an edge port receives a BPDU?()

題型:多項選擇題

During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()

題型:單項選擇題

Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()

題型:單項選擇題

Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()

題型:單項選擇題

Refer to the exhibit. Which statement is true about the output?()

題型:單項選擇題

What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals?()

題型:單項選擇題

Refer to the exhibit. For what purpose is the command show ip cef used?()

題型:單項選擇題

Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()

題型:單項選擇題