A. Summarized routes are unacceptable
B. They will appe ar in the OSPF routing table as type E2 routes
C. Only routes with lower administrative distances will be imported
D. All imported routes are to be automatically summarized if possible
您可能感興趣的試卷
你可能感興趣的試題
A. RIP
B. BGP
C. IS - IS
D. OSPF
E. EIGRP
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）
A. The redistribution command should be reentered with the match route - type parameter included.
B. The redistribution command should be reentered wit h the route - map map - tag parameter included.
C. The redistribution command should be reentered with the metric metric - value parameter included.
D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?（）
A. Interface authentication must be configured
B. The routing processes must be configured with an area ID
C. IP unicast routing must be enabled
D. IPv4 ad dresses must be applied to the interfaces
Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?（）
A. the serial 1/1 address
B. the serial 2/0 address
C. a randomly generated internal address
D. the configured router - id address
A.Interfaces have a default metric of 1.
B.Level 1 is intra - area and level 2 is interarea.
C.Level 1 routing is between an end system (ES) and IS while Level 2 routing is between an IS and IS.
D. Hosts send ISHs while routers send ESHs.
E. IS - IS is an open standard.
F. Metrics depend on interface speed.
最新試題
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive