Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）
A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. What is the effect of the OSPF configuration on router B?（）
A. All interfaces will be in area 0
B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1
C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2
D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.
What can you conclude about router A?（）
A. Only the router A loopback interface is parti cipating in the OSPF routing process
B. None of the router A interfaces are participating in the OSPF routing process
C. Router A is using the loopback interface IP address as its OSPF router ID
D. Router A does not have any reachable OSPF neighbors
Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly. What can you conclude from the exhibit and the show running - configuration command output? （）
A. The OSPF areas are not configured correctly.
B. The wildcard masks for the 10.x .x.x networks are incorrect.
C. The 172.16.x.x networks need to be connected to area 0 using virtual links.
D. The 172.16.x.x networks are discontiguous. OSPF is automatically summarizing them to 172.16.0.0/16 and data is being "black holed."
E. There is not enough information to make a determination.
Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）
A. An access list on router B is causing the 192.168.3.16/28 network to be denied
B. An access list on router B is causing the 192.168.3.32/28 network to be denied
C. The distribute list on router B is referencing a numbered access list that does not exist on router B
D. The d istribute list on router B is referencing the wrong interface
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:
What information can you determine about this network?（）
A. The network is stable
B. There is a flapping link or interface, and router C knows an alternate path to the network
C. There is a flapping link or interf ace, and router C does not know an alternate path to the network
D. EIGRP is not working correctly on router C
E. There is not enough information to make a determination
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Which of the following features work the same in both RIP- 2 and RIPng?（）