Which of the following answers can be verified as true based on the following command output from Router R1?()
R1#show ip ospf virtual - links
Virtual Link OSPF_VL0 to router 4.4.4.4 is up
Run as demand circuit
DoNotAge LSA alloweD.
Transit area 1, via interface FastEthernet0/1, Cost of using 3
A. R1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.
B. The ping 4.4.4.4 command on R1 must currently be successful.
C. R1's Fa0/0 OSPF cost is 3.
D. 4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
您可能感興趣的試卷
你可能感興趣的試題
A. Stub
B. Totally stubby
C. NSSA
D. Totally NSSA
A. Routers cannot redistribute external routes into the area.
B. Routers should have zero Type 3 LSAs in their LSDBs.
C. Routers should have zero Type 5 LSAs in their LSDBs.
D. Routers should learn default routes from the ABRs attached to the area.
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command.
Which of the following is true about the effects of this configuration command?()
A. R1 will always create and flood a default route into the OSPF domain.
B. R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.
C. R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.
D. R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
The following output exists on Router R1, a router internal to area 1. What can you d etermine as true from the output of the show ip ospf database summary command?()
A. The LSA was created by an ABR due to an area range command.
B. The LSA was created by an ASBR due to a summary - address command.
C. If cr eated by an area range command, the best metric for a subordinate subnet on that ABR must have been 11.
D. None of the other answers is correct.
R1, an ABR between backbone area 0 and area 1, has intra - area routes in area 0 for 10.1.1.0/24,10.1.2.0/24, and 10.1.3.0/24. These routes have metrics of 21, 22, and 23, respectively. An engineer then adds the area 0 r ange 10.1.0.0 255.255.0.0 command under the OSPF process of R1.
Which of the following is true?()
A. R1 loses and then re - establishes neighborships with all neighbors.
B. R1 no longer advertises 10.1.1.0/24 to neighbors into area 1.
C. R1 advertises a 1 0.1.0.0/16 route into area 1 with a metric of 23 (largest metric).
D. R1 advertises a 10.1.0.0/16 route into area 1 with metric of 21 (lowest metric).
最新試題
Which of the following answers lists a multicast IPv6 address?()
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?()interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?()