A.Clients connected to the rogue access point must be able to connect to the containmentcontroller-based access point.
B.Multiple controller-based access points will load-balance the containment task using fewerresourcesthan a single access point.
C.Clients connected to the rogue access point may be out of the range of the controller-basedaccess point providing containment.
D.Each controller-based access point can handle only a limited amount of clients connected tothe rogue access points.
您可能感興趣的試卷
你可能感興趣的試題
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.
Before you press and hold the MODEbutton，you should verify that the file name is which of the following？ （）
A.c1130-k9w7-tar.boot
B.c1130-k9w7-tar.123-7.JA1.tar
C.c1130-k9w7-tar.default
D.c1130-k9w7-tar.recover
A.Problem Management
B.Configuration Management
C.Incident Management
D.Change Management
A.15
B.10
C.1
D.5
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A clientthat is anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective？（）
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
You are charged with implementing a secure wireless installation which will provide Internet
access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actionsshould you perform on the wired infrastructure？（）
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action， you have achieved your goal.
D.Implement a protected port on the access switches.
最新試題
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）