A. a request made by a node to join a specified multicast group
B. a request made by a node for its IP address
C. a request made by a node for the IP address of the DHCP server
D. a request made by a node for the IP address of the local router
您可能感興趣的試卷
你可能感興趣的試題
To enable BGP tunneling over an IPv4 backbone, the IPv4 address 192.168.30.1 is converted into a valid IPv6 address.
Which three IPv6 addresses are acceptable formats for the IPv4 address? （）
A. 192.168.3 0.1:0:0:0:0:0:0
B. 0:0:0:0:0:0:192.168.30.1
C. ::192.168.30.1
D. C0A8:1E01::
E. 192.168.30.1::
F. ::C0A8:1E01
Refer to the exhibit. Based on the output from the show command on RT1which statement is true? （）
A. OSPFv3 uses global IPv6 addresses to establish neighbor adjacencies.
B. RT1 has a subnet mask of 64 bits .
C. RT1 has FastEthernet0/0 set as a DR for network type broadcast.
D. OSPFv3 uses Link - local addresses to establish neighbor adjacencies.
E. RT1does not have a global IPv6 address set on FastEthernet0/0.
F. OSPFv3 uses IPv4 addresses to establish nei ghbor adjacencies.
A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.
B. It must be issued after the network command to enable the OSPF process for IPv6.
C. It must be issued in router global configuration mode to enable the OSPF process for IPv6.
D. It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.
In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes.
Which statement is true about the IPv6 addresses that can be included into the OSPF process?" （）
A. Specific addresses can be selected using a prefix list.
B. Specific addresses can be selected using a route map.
C. Specific addresses cann ot be selected for importation into the OSPF process.
D. Specific addresses can be selected using an ACL.
A. The shortest path first (SPF) algorithm is performed on the LSA database.
B. The OSPF adjacencies are cleared and initiated again.
C. The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.
D. The route table is cleared. Then the OSPF neighbors are reformed.
最新試題
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following answers lists a multicast IPv6 address?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0